|
麥迪奧派對用品專門店
|
|
|
|
|
|
|
|
|
|
|
|
| ● Balloon Seal with Ribbon |
|
 |
Grasp the ribbon attached to the clip and unravel. Inflate the balloon and twist the neck several times. Pull the twisted balloon neck through one slot on the clip, positioning the balloon so it sits upright in the base of the clip. |
|
 |
To secure, loop the balloon neck around the stem of the clip and
through the second slot, tucking the end inside the base of the clip. (It is not necessary to wrap the balloon neck around the entire clip.) |
|
| TOP |
| ● Fold Napkin |
|
| French Pleat |
    |
- Fold napkin in quarters
- Roll the first layer of the napkin toward you to the center
- Fold the second layer toward you and under the first - Do not Roll.
- Leave the same width of the napkin as the rolled edge.
- Fold the next layer of the napkin away from you and under the second leaving the same width as other two folds.
- Fold under the right and left side edges to center back.
|
|
| Crown |
    |
- 1. Fold the napkin in half diagonally forming a triangle.
- Fold the left and right triangle to the top forming a square.
- Turn the napkin to form a diamond. Fold the bottom point 2/3 of the way to the top point and fold the bottom point back again to the base line.
- Turn napkin over and tuck the far corners into one another forming a round base.
- Stand a napkin upright and flair out the two top corners to form a Crown.
|
|
| Goblet Fan |
    |
- 1. Fold napkin in half with the edges at the bottom
- Fold napkin in half with the edges at the bottom
- Accordion pleat form right to left.
- Fold the bottom third up.
- Insert into goblet and spread pleat to form fan
|
|
| Opera Fan |
|
    |
- Fold napkin in half.
- Fold width into accordion
- Fold leaving last four inches flat.
- Fold accordion in half with folds on outside; four inch flat will protrude from the center.
- Create a stand by folding the four inch flat toward the base of napkin letting the folds fan out.
|
|
| Rose |
    |
- Fold all four corners of a flat napkin into the center: then fold four points again to the center.
- Turn the napkin over and fold four points again to the center pressing all folds tightly.
- Turn napkin to form a diamond. Using one hand to hold two points at front center of the napkin and with the other hand reach under that point and pull up flap.
- Repeat at three other points.
- Holding center points, reach between petals and pull out additional flaps.
|
| |
|
| TOP |
| ● Pull String Bows |
|
   |
| Grasp the ribbon attached to the clip and unravel. Inflate the balloon and twist the neck several times. Pull the twisted balloon neck through one slot on the clip, positioning the balloon so it sits upright in the base of the clip. |
|
| TOP |
| ● Balloon FAQ |
|
What size straw should I use on a 9" foil?
We recommend that you use a 16" or 24" straw.
Are 18", oversized or helium shaped foil balloons self-sealing?
Yes. When an 18", oversized or helium shaped foil is inflated to the correct size, the pressure of the helium inside the balloon closes the valve. If the ribbon is attached below the inflation point, foil balloons can be re-inflated.
How do you seal an air-filled micro or mini foil?
To seal a mini or micro foil balloon, a heat sealer is required. BWI carries 4" heat sealers. After inflating the foil balloon, lay the neck flat and press the arm of the heating element down firmly on the neck. Make sure the light is on and hold for approximately three seconds.
What kind of clip should I use?
For 11" latex balloons, use small clips; for larger latex balloons, use jumbo clips. Clips are not recommended for use on foil balloons. (See page 171 of BWI's Balloon Solutions Catalog for clip information)
What is the standard ribbon size?
3/16" is the standard ribbon size, but some people prefer the wider 3/8" ribbon. Sizes and the full color line of ribbon are shown on pages 164-165 of BWI's Balloon Solutions Catalog.
Why do I need a special inflator for my foils?
The opening in the neck of a foil balloon requires a special tip that allows the foil balloon to be inflated without stretching the valve. With the proper inflation, balloons will float longer. The Precision Plus Inflator automatically shuts off when the balloon is fully inflated, eliminating costly breakage. (See page 170 of BWI's Balloon Solutions Catalog)
What is Ultra Hi-Float™?
Ultra Hi-Float™ is a water soluble plastic formulated to hold helium inside latex balloons. It can extend the float time by up to 10 times. (See page 171 of BWI's Balloon Solutions Catalog)
How does Ultra Hi-Float™ work?
Ultra Hi-Float™ dries inside the latex, creating a thin coating which seals the tiny pores that naturally occur in latex.
How much Ultra Hi-Float™ do I need for each balloon?
Each 11" latex ballon requires approximately a dime size drop of Ultra Hi-Float™. 96 ounces (approx. one gallon) will treat 540 11" latex balloons. BWI can provide more information on other sizes. |
|
|
| TOP |
| ● Cool Air Inflator |
|
  |
Premium Balloon Accessories is pleased to introduce their new portable, battery-powered, high-pressure inflator specifically designed for all sizes modeling balloons for Twisters, Clowns, and Professional Entertainers, The NEW Premium Twist-N-Flate has been designed, engineered and will be manufactured to the very high quality Premium standards to provide years of reliable, long-term use. Features & Benefits Include:
- Lightweight and Portable
- Designed to easily inflate 160&260 modeling balloons ONLY, without pre-stretching.
- Unique “Activation Switch” for high speed single-handed nozzle attachment and inflation of balloon.
- “Activation Switch” designed for night or left hand use with any portion of the hand or finger.
- High-Powered Battery will run about 3 hours, generally long enough to inflate up to 500 balloons.
- “Quick-Change” battery compartment for quick, simple change of battery.
- Wireless connection of the battery within the compartment for efficient, trouble-free battery changes.
- “Battery Level Indictor”, shows current charge, Green (3/3 charge) to Yellow (2/3 charge) to Red (1/3 charge).
- Universal, world-wide battery charger with, short cord set for Euro, UK, USA, Australian and Japan.
- Battery can be charged during use for extended performance.
- Universal nozzle tip is designed to fit both 160 & 260 modeling balloons.
- Premium quality engineering and materials for lasting performance and reliability.
- CE Approval for European and worldwide sales distribution is coming soon!
- Spare Battery, Battery Charger, Waist Scrap and Basket Accessories available.
|
|
| TOP |
|
|
| Add To Bookmarks
